电子温度计 家用室内温湿度计 婴儿高精度闹钟夜光HTC-8
店铺热销
商品属性
供应商
商品描述
HTC-8 夜光温湿度计 时钟
基本特征：
1.温度，湿度，年月日，时钟，同屏显示
2.12/24 小时制的时钟
3.每日闹钟、整点报时功能
4.℃/℉温度显示。温度与湿度最高最低记忆
5.夜光功能
6.温度测量范围：0~50℃（-32~122℉）
7.温度分辨率显示：0.1℃（0.2℉）
8.温度测量精度：±0.5℃（0℃~50℃）,其它±1℃
9.湿度测量范围：10%RH~99%RH
10.产品尺寸：175X60X25mm
操作说明：
1.夜光的开启，摇一摇机身点亮夜光，5秒后自动熄灭。
2.温度单位的切换
在机身背面按[℃/℉]温度单位键切换温度显示单位。
3.记忆的查看与清除
在机身背面按[MEMORY]记忆键可查看记忆中最高(MAX)/最低(MIN)温湿度值，在显示最高(MAX)/最低(MIN)温湿度值时，长按[MEMORY]记忆键清除记忆中的最高(MAX)/最低(MIN)温湿度值。
4.日期时钟的设定
在显示时钟的时候，长按[MODE]模式键开始依次设定时钟的分钟→小时12/24小时制→年→月→日，按[ADJ]调整键调整。再按[MODE]模式键确认设定的时钟与日期。
5.闹钟时间的设定
在显示时钟的时候，短按[MODE]模式键切换到闹钟的显示，再长按[MODE]模式键开始依次设定闹钟的分钟→小时，按[ADJ]调整键调整。再按[MODE]模式键确认设定的闹钟时间。
6.闹钟与整点报时的开启与关闭
在显示时钟的时候，短按[MODE]模式键切换到闹钟的显示，按[ADJ]调整键开启/关闭闹钟或整点报时，顺序是：闹钟开→整点报时开→闹钟与整点报时同时开→闹钟与整点报时都关。
本产品使用1.5V X 2 AAA电池
字体显示模糊，请更换电池
HTC-8 luminous temperatureand humidity meterclock manual
The basicfeaturesof：
- 1. Temperature, humidity, date(year、mouth、day), clock, with screen display
- 2. Clock for 12/24 hours
- 3. Daily alarm。The whole point timekeeping function
- 4. ℃/℉temperature display。The maximum and minimum memory of temperature and humidity
- 5. Luminousfunction
- 6. Temperature measurement range：0℃~50℃(-32℉~122℉)
- 7. Temperature display resolution：0.1℃(0.2℉)
- 8. The temperature measurement precision:±0.5℃(0℃~50℃),others±1℃
- 9. Humidity measurement range: 10%RH~99%RH
Operating instructions：
- 1. The luminous opens：Press the button of light icon to lit luminous, automatically extinguished after 5 seconds.
- 2. Switching temperature unit:
Press the [℃/℉] buttonto switch temperature display unit.
3.Checkand clean the memory:
Press the [MEMORY] memory button can check the maximum (MAX)/minimum (MIN) temperature and humidity value in the memory. When see Maximum (MAX)/ minimum (MIN) temperature and humidity value in display, press and hold the [MEMORY] memory button to clean the maximum (MAX)/minimum (MIN) temperature and humidity value in the memory.
4. The date and clocksetting:
When display the clock,press hold the [MODE] buttonstart to set the clockfollowed by minutes→hours→12∕24hours→year→mouth→day, press the [ADJ] key to adjust, then press the [MODE] button to confirm the clock and date.
5.The alarm time setting:
When display the clock,press [MODE]buttonto switch to the alarm display,and then press and hold the [MODE] button start to set thealarm timefollowed byminutes→hours, press the [ADJ]buttonto adjust. Then press the [MODE] button again to confirm the alarm time setting.
6.The alarm clock and the whole point timekeeping opening and closing
When display the clock,press [MODE]buttonto switch to the alarm display, and then press the [ADJ]buttonto open and close alarm clock or the whole point timekeeping, followed by the alarm clock opened－>the whole point timekeeping opened－>both the alarm clock and the whole point timekeeping opened－> both the alarm clock and the whole point timekeeping closed.
Note:
1. This machine for precision instruments, users to remove the damage is beyond the scope of the warranty.
2. The battery after use, please back the government designated collection points.
